Set Dialogic Voice Board Low-Level Parameters
$cpb_parm line parm=parmstring
This command allows setting of low-level voice-board parameters on a per-channel basis. Please consult Copia or your CopiaFacts supplier before using this command. Incorrect settings can disrupt the operation of your system and may also invalidate the PTT approval of your board.
The parameters on this command are used as follows:
| line | the line number or line group(s) affected, or * for all lines. The same line must not be specified more than once. |
| parmstring | a parameter specification as described below. |
The parameter specification uses a keyword=value syntax with the keyword selected from the list below. Only one keyword value can be specified per command, but you may use multiple commands to set all the values you need. Most time values are specified in 10ms units unless otherwise indicated. Valid keywords for Dialogic boards are as follows:
| dflags | DTMF detection edge select |
| dtinitset | DTMF digits bitmask to initiate play |
| dtmftlk | Minimum time for DTMF to be present (dft 5) |
| dtmfdeb | DTMF debounce time (dft 0, -1 to suppress) |
| mfmode | 0/2 for 40ms/65ms MF tone detection |
| maxrwink | max time LC on to recognize Wink (dft 20) |
| minrwink | min time LC on to recognize Wink (dft 10) |
| winkdly | delay after ring received before Wink (dft 15) |
| ringcnt | rings to wait before ring event (dft 4) |
| winklen | duration of off-hook for Wink (dft 15) |
| playdrate | default dig rate for playback (dft 6000) |
| recrdrate | default dig rate for record (dft 6000) |
| nbrdna | # of rings before no answer |
| stdely | Delay after dialing before analysis |
| cnosig | Duration of no signal time out delay |
| lcdly | Delay after dial before lc drop connect |
| lcdly1 | Delay after lc drop con. before msg |
| hedge | Edge of answer to send connect message |
| cnosil | Initial continuous noise timeout delay |
| lo1tola | % acceptable pos. dev of short low sig |
| lo1tolb | % acceptable neg. dev of short low sig |
| lo2tola | % acceptable pos. dev of long low sig |
| lo2tolb | % acceptable neg. dev of long low sig |
| hi1tola | % acceptable pos. dev of high signal |
| hi1tolb | % acceptable neg. dev of high signal |
| lo1bmax | Maximum interval for short low for busy |
| lo2bmax | Maximum interval for long low for busy |
| hi1bmax | Maximum interval for 1st high for busy |
| nsbusy | Num. of highs after nbrdna busy check |
| logltch | Silence deglitch duration |
| higltch | Non-silence deglitch duration |
| lo1rmax | Max. short low dur. of double ring |
| lo2rmin | Min. long low dur. of double ring |
| intflg | Operator intercept mode |
| intfltr | Minimum signal to qualify freq. detect |
| spdeb | Trailing edge silence ptr debounce |
| hisiz | Used to determine which lowmax to use |
| alowmax | Max. low before con. if high >hisize |
| blowmax | Max. low before con. if high <hisize |
| nbrbeg | Number of rings before analysis begins |
| hi1ceil | Maximum 2nd high dur. for a retrain |
| lo1ceil | Maximum 1st low dur. for a retrain |
| lowerfrq | Lower allowable frequency in Hz |
| upperfrq | Upper allowable frequency in Hz |
| timefrq | Total duration of good signal required |
| rejctfrq | Allowable % of bad signal |
| maxansr | Maximum duration of answer |
| ansrdgl | Silence deglitching value for answer |
| mxtimefrq | Max. time for first frequency to remain in bound |
| lower2frq | Lower bound for second frequency |
| upper2frq | Upper bound for second frequency |
| time2frq | Min. time for second frequency to remain in bound |
| mxtime2frq | Max. time for second frequency to remain in bound |
| lower3frq | Lower bound for third frequency |
| upper3frq | Upper bound for third frequency |
| time3frq | Min. time for third frequency to remain in bound |
| mxtime3frq | Max. time for third frequency to remain in bound |
| dtn_pres | length of valid dial tone |
| dtn_npres | max time to wait for dial tone |
| dtn_deboff | dialtone off debouncer |
| pamd_failtime | Wait for PAMD/PVD after cadence break in 10ms |
| pamd_minring | Min. allowable ring duration |
| pamd_spdval | full/quick PAMD decision |
| pamd_qtemp | Qualification to use for PAMD |
| noanswer | noanswer after 1st ring |
| maxintering | inter-ring delay before connect |
Example:
$cpb_parm * noanswer=1500
Topic url:
http://www.copia.com/support/refmanual/index.html?$cpb_parm.htm
