|
$mcb_parm [CFG] |
  
|
|
$mcb_parm [CFG] |
|
Set Dialogic PRI Board Make-Call Parameters
$mcb_parm board parm=parmstring
This command allows setting of low-level parameters in the PRI make-call block on a per-board basis. Please consult Copia or your CopiaFacts supplier before using this command. Incorrect settings can disrupt the operation of your system and may also invalidate the PTT approval of your board.
The parameters on this command are used as follows:
| board | the board number (x in dtiBx) affected, or * for all telephony boards. |
| parmstring | a parameter specification as described below. |
The parameter specification uses a keyword=value syntax with the keyword selected from the list below. Only one keyword and two-digit hexadecimal value can be specified per command, but you may use multiple commands to set all the values you need. Valid keywords and default values are as follows:
| bc_xfer_cap | E1: 00 T1: 00 |
BEAR_CAP_SPEECH 00 Speech Bearer Capability
BEAR_CAP_UNREST_DIG 08 Unrestricted Digital Capability
BEAR_CAP_REST_DIG 09 Restricted Digital Capability
BEAR_CAP_3DOT1K_AUDIO 10 3.1KHz Audio Capability
BEAR_CAP_7K_AUDIO 11 7KHz Audio Capability
BEAR_CAP_VIDEO 18 Video Capability
| bc_xfer_mode | E1: 00 T1: 00 |
ISDN_ITM_CIRCUIT 00 info transfer mode - circuit mode
ISDN_ITM_PACKET 02 info transfer mode - packet mode
| bc_xfer_rate | E1: 10 T1: 10 |
BEAR_RATE_64KBPS 10 B_CHANNEL_UNITS 1X64
| usrinfo_layer1_protocol | E1: 03 T1: 02 |
ISDN_UIL1_CCITTV110 01 user info layer 1 - CCITT V.110/X.3
ISDN_UIL1_G711ULAW 02 user info layer 1 - G.711 u-law
ISDN_UIL1_G711ALAW 03 user info layer 1 - G.711 A-law
ISDN_UIL1_G721ADCPM 04 user info layer 1 - G.721 ADCPM
ISDN_UIL1_G722F725 05 user info layer 1 - G.722 and G.725
ISDN_UIL1_H261 06 user info layer 1 - H.261
ISDN_UIL1_NONCCITT 07 user info layer 1 - non-CCITT
ISDN_UIL1_CCITTV120 08 user info layer 1 - CCITT V.120
ISDN_UIL1_CCITTX31 09 user info layer 1 - CCITT X.31
ISDN_UIL1_DEFAULT FF user info layer 1 - Default Value
| usr_rate | E1: 00 T1: FF |
ISDN_UR_EINI460 00 user rate - E bits in I.460
ISDN_UR_600 01 user rate - 0.6 kbits
ISDN_UR_1200 02 user rate - 1.2 kbits
ISDN_UR_2400 03 user rate - 2.4 kbits
ISDN_UR_3600 04 user rate - 3.6 kbits
ISDN_UR_4800 05 user rate - 4.8 kbits
ISDN_UR_7200 06 user rate - 7.2 kbits
ISDN_UR_8000 07 user rate - 8.0 kbits
ISDN_UR_9600 08 user rate - 9.6 kbits
ISDN_UR_14400 09 user rate - 14.4 kbits
ISDN_UR_16000 0A user rate - 16.0 kbits
ISDN_UR_19200 0B user rate - 19.2 kbits
ISDN_UR_32000 0C user rate - 32 kbits
ISDN_UR_48000 0E user rate - 48 kbits
ISDN_UR_56000 0F user rate - 56 kbits
ISDN_UR_64000 10 user rate - 64 kbits
ISDN_UR_134 15 user rate - .1345 kbits
ISDN_UR_100 16 user rate - .100 kbits
ISDN_UR_75_1200 17 user rate - .075/1200 kbits
ISDN_UR_1200_75 18 user rate - 1200/.075 kbits
ISDN_UR_50 19 user rate - .050 kbits
ISDN_UR_75 1A user rate - .075 kbits
ISDN_UR_110 1B user rate - .110 kbits
ISDN_UR_150 1C user rate - .150 kbits
ISDN_UR_200 1D user rate - .200 kbits
ISDN_UR_300 1E user rate - .300 kbits
ISDN_UR_12000 1F user rate - 12 kbits
ISDN_UR_DEFAULT FF user rate - Default
| destination_number_type | E1: 00 T1: 02 |
EN_BLOC_NUMBER 00 Number is sent en-bloc
INTL_NUMBER 01 International number
NAT_NUMBER 02 National number
LOC_NUMBER 04 Local (directory) number
OVERLAP_NUMBER 05 Number is sent overlap
| destination_number_plan | E1: 01 T1: 01 |
UNKNOWN_NUMB_PLAN 00 Unknown plan
ISDN_NUMB_PLAN 01 ISDN numb. plan E.164
TELEPHONY_NUMB_PLAN 02 Telephony numb. plan E.163
PRIVATE_NUMB_PLAN 09 Private numbering plan
| destination_sub_number_type | E1: 00 T1: FF |
EN_BLOC_NUMBER 00 Number is sent en-bloc
INTL_NUMBER 01 International number
NAT_NUMBER 02 National number
LOC_NUMBER 04 Local (directory) number
OVERLAP_NUMBER 05 Number is sent overlap
disable ff Don't send this info element
| destination_sub_number_plan | E1: 00 T1: FF |
UNKNOWN_NUMB_PLAN 00 Unknown plan
ISDN_NUMB_PLAN 01 ISDN numb. plan E.164
TELEPHONY_NUMB_PLAN 02 Telephony numb. plan E.163
PRIVATE_NUMB_PLAN 09 Private numbering plan
disable ff Don't send this info element
| origination_number_type | E1: 02 T1: 02 |
EN_BLOC_NUMBER 00 Number is sent en-bloc
INTL_NUMBER 01 International number
NAT_NUMBER 02 National number
LOC_NUMBER 04 Loacl (directory) number
OVERLAP_NUMBER 05 Number is sent overlap
disable ff Don't send this info element
| origination_number_plan | E1: 01 T1: 01 |
UNKNOWN_NUMB_PLAN 00 Unknown plan
ISDN_NUMB_PLAN 01 ISDN numb. plan E.164
TELEPHONY_NUMB_PLAN 02 Telephony numb. plan E.163
PRIVATE_NUMB_PLAN 09 Private numbering plan
disable ff Don't send this info element
| origination_sub_number_type | E1: 00 T1: FF |
EN_BLOC_NUMBER 00 Number is sent en-bloc
INTL_NUMBER 01 International number
NAT_NUMBER 02 National number
LOC_NUMBER 04 Loacl (directory) number
OVERLAP_NUMBER 05 Number is sent overlap
disable ff Don't send this info element
| origination_sub_number_plan | E1: 00 T1: FF |
UNKNOWN_NUMB_PLAN 00 Unknown plan
ISDN_NUMB_PLAN 01 ISDN numb. plan E.164
TELEPHONY_NUMB_PLAN 02 Telephony numb. plan E.163
PRIVATE_NUMB_PLAN 09 Private numbering plan
disable ff Don't send this info element
| facility_feature_service | E1: 01 T1: FF |
ISDN_FEATURE 00 feature/service - feature
ISDN_SERVICE 01 feature/service - service
disable ff Don't send this info element
| facility_coding_value | E1: FF T1: FF |
ISDN_CPN_PREF 01 facility coding - CPN perferred
ISDN_SDN 01 service coding - SDN
ISDN_BN_PREF 02 facility coding - BN preferred
ISDN_ACCUNET 06 service coding - ACCUNET SDS
ISDN_LONG_DS 07 service coding - Long distance
ISDN_INT_800 08 service coding - internation 800
ISDN_CA_TSC 09 service coding - CA TSC
ISDN_ATT_MULTIQ 10 service coding - ATT MultiQuest
disable ff Don't send this info element
Example:
$mcb_parm * origination_number_plan=00 ; unknown number plan
$mcb_parm * destination_number_plan=00 ; unknown number plan
Topic url: http://www.copia.com/support/refmanual/index.html?%24mcb_parm.htm